Manual No. 203768GS Revision A (03/31/2008)BRIGGS & STRATTON POWER PRODUCTS GROUP, LLCJEFFERSON, WISCONSIN, U.S.A.Pressure WasherOperator’s Manua
Connect Hose and Water Supply to PumpNOTE: Remove and discard the shipping caps from thepump’s high pressure outlet and water inlet before attachingho
11Features and ControlsRead this Operator’s Manual and safety rules before operating your pressure washer.Compare the illustrations with your pressure
OperationIf you have any problems operating your pressure washer,please call the pressure washer helpline at (800) 743-4115.Pressure Washer LocationCl
13How to Start Your Pressure WasherTo start your pressure washer for the first time, follow theseinstructions step-by-step. This starting information
12. Return starter grip handle slowly. DO NOT let rope“snap back” against starter.13. When engine starts, slowly move choke lever to “Run” position, a
15How to Use Accessory TrayThe unit is equipped with an accessory tray with places tostore your spray gun, nozzle extension and ProjectPro®nozzles. Th
2. Select desired ProjectPro® nozzle:• For delicate rinse (lower pressure and higher flow),for gentle cleaning of cars/trucks, boats, RV’s, patiofurni
175. Make sure garden hose is connected to water inlet.Check that high pressure hose is connected to spraygun and pump. Turn on water.6. Start engine
18 BRIGGSandSTRATTON.COMMaintenanceMaintenance ScheduleFollow the hourly or calendar intervals, whichever occursfirst. More frequent service is requir
19Check High Pressure HoseThe high pressure hose can develop leaks from wear,kinking, or abuse. Inspect the hose each time before using it.Check for c
2 BRIGGSandSTRATTON.COMBriggs & Stratton Power Products Group, LLC900 North ParkwayJefferson, WI 53549Copyright © 2008 Briggs & Stratton Powe
Engine MaintenanceOilOil RecommendationsWe recommend the use of Briggs & Stratton WarrantyCertified oils for best performance. Other high-qualityd
214. Remove oil drain plug and drain oil completely into asuitable container.5. Reinstall oil drain plug and tighten securely. Remove oilfill cap.6. S
Air Cooling SystemOver time debris may accumulate in cylinder cooling fins andcannot be observed without partial engine disassembly. Forthis reason, w
23Winter StorageTo protect the unit from freezing temperatures:1. Follow steps 1-4 in the previous section After Each Use.2. Use pump saver, Model 603
Troubleshooting24 BRIGGSandSTRATTON.COMProblem Cause CorrectionPump has following problems: failureto produce pressure, erratic pressure,chattering, l
25WarrantiesEmissions Control System WarrantyBriggs & Stratton Corporation (B&S), the California AirResources Board (CARB) and the United Stat
26 BRIGGSandSTRATTON.COM2. Length of CoverageB&S warrants to the initial owner and each subsequentpurchaser that the Warranted Parts shall be free
27BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC PRESSURE WASHER OWNER WARRANTY POLICYLIMITED WARRANTYBriggs & Stratton Power Products Group, LLC
28 BRIGGSandSTRATTON.COMBriggs & Stratton Power Products Group, LLC900 N. ParkwayJefferson, Wisconsin, 53549 U.S.A.Pressure WasherPower Ratings:
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLCJEFFERSON, WISCONSIN, U.S.A.Limpiadora a presiónManual del OperarioEsta limpiadora a presión está clasi
Table of ContentsOperator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Equipment Description. . . . . . . . . . . . . . .
2 BRIGGSandSTRATTON.COMBriggs & Stratton Power Products Group, LLC.900 North ParkwayJefferson, WI 53549Copyright © 2008 Briggs & Stratton Pow
3EspañolTabla de ContenidoSeguridad de Operario . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Derscripción del equipo. . . . . . . . . . .
Seguridad de OperarioDerscripción del equipoLea este manual de manera cuidadosa yfamiliarícese con su limpiadora a presión.Conozca sus usos, sus limit
5EspañolADVERTENCIAEl escape del motor de este producto contieneelementos químicos reconocidos en el Estado deCalifornia por producir cáncer, defectos
6 BRIGGSandSTRATTON.COMADVERTENCIAEl retroceso (repliegue rápido) del cable delarrancador puede producir lesiones. El retrocesoimpedirá que el usuario
7EspañolAVISOEl rociado de alta presión puede dañar elementos frágiles,incluyendo el vidrio.• NO dirija la pistola rociadora hacia un cristal cuando u
MontajeLea totalmente el manual del operario antes queintente ensamblar u operar su limpiadora a presión.Su limpiadora a presión requiere de ciertos p
Agregar aceite al motor1. Coloque la limpiadora a presión en una superficie planay nivelada.2. Limpie la zona de alrededor del orificio de llenado dea
Conecte la manguera y el suministro de agua ala bombaNOTA: Antes de conectar las mangueras, retire y deseche lostapones de transporte de la salida de
A - Boquillas ProjectPro® – Detergente, 0º, 25º: para diferentesalta presión aplicaciones de limpieza.B - Pistola de Rociado — Controla la aplicación
Operator SafetyEquipment DescriptionRead this manual carefully and become familiarwith your pressure washer. Know its applications,its limitations, an
OperandoSi tiene problemas operando su máquina limpiadora apresión, por favor llame a la línea de ayuda para máquinaslimpiadora a presión al (800) 743
9. Mueva el control de la válvula de admisión (A) a laposición "Rápido" ("Fast") , que se distingue con lafigura de un conejo.10.
13. Cuando arranque el motor, mueva lentamente lapalanca del ahogador a la posición "En marcha" ("Run"). Si el motor falla, mueva
Utilización de la bandeja de accesoriosLa unidad está equipada con una bandeja de accesorios conhabitáculos para guardar la pistola rociadora, el prol
2. Elija la boquilla ProjectPro® que desee:• Para un enjuagado suave (baja presión y mayorcaudal), para una limpieza suave de coches/camiones,barcos,
4. Asegúrese de que la boquilla de detergenteProjectPro® negra está montada.NOTA: NO se puede aplicar detergente con las boquillas dealta presión (Ama
MantenimientoPlan de mantenimientoSiga los intervalos de horas o de calendario, los que sucedanantes. Si opera en condiciones adversas (señaladas mása
Revise y limpie el colador de entradaExamine el colador de entrada de la manguera de jardín.Límpielo si está tapado o remplacelo si está roto.Revise l
Mantenimiento de los anillos 'o'Compre una O–Juego de Mantenimiento de Anillo, el modelo6048, en avisando el más cercano servicio autorizado
Cambio de aceite del motorCambie el aceite después de las primeras 5 horas deoperación. Cambie el aceite cada 50 horas de ese momentoen adelante. Si e
5WARNINGThe engine exhaust from this product contains chemicalsknown to the State of California to cause cancer, birthdefects, or other reproductive h
4. Cambie la bujía si los electrodos están picados oquemados o si la porcelana está agrietada. Utilice labujía de repuesto recomendada. ConsulteEspeci
23EspañolAlmacenamiento para inviernoPara proteger la unidad de las temperaturas decongelamiento:1. Siga los pasos 1-4 en la sección previa Despues de
24 BRIGGSandSTRATTON.COMProblema Causa SoluciónLa bomba presenta lossiguientes problemas: noproduce presión o produce unapresión errada, traqueteo,pér
GARANTÍASGarantía del sistema de control de emisionesBriggs & Stratton Corporation (B&S), el California AirResources Board (CARB, Consejo de r
26 BRIGGSandSTRATTON.COMe. Elementos diversos utilizados en los sistemasanteriores• Válvulas y conmutadores de aspiración,temperatura, posición y temp
27Español2 año90 díasUso del consumidorUso comercialPOLÍTICA DE GARANTÍA PARA EL PROPIETARIO DE UNA LAVADORA A PRESIONBRIGGS & STRATTON POWER PROD
28 BRIGGSandSTRATTON.COMBriggs & Stratton Power Products Group, LLC900 N. ParkwayJefferson, Wisconsin, 53549 U.S.A.Limpiadora a PresiónPotencia
6 BRIGGSandSTRATTON.COMWARNINGStarter cord kickback (rapid retraction) can resultin bodily injury. Kickback will pull hand and armtoward engine faster
7NOTICEHigh pressure spray may damage fragile items includingglass.• DO NOT point spray gun at glass when using red 0° nozzle.• NEVER aim spray gun at
AssemblyRead entire operator’s manual before you attemptto assemble or operate your new pressure washer.Your pressure washer requires some assembly an
Add Engine Oil1. Place pressure washer on a flat, level surface.2. Clean area around oil fill and remove yellow oil fill cap.3. Using oil funnel (opti
Comments to this Manuals