Briggs-stratton PRO6500 User Manual download pdf (Page 7)

BSPP Generator

2. Slide axle through both axle mounting brackets on

cradle frame, as shown in Figure 1.

3. Slide a wheel over the axle.

NOTE: Be sure to install both wheels with the air

pressure valve on the outboard side.

4. Slide a flat washer over the axle and place the e-ring

onto the groove in the axle.

5. Place one end of the needle nose pliers on the bottom

of the axle and the other end of the pliers on top of

the e-ring. Seat the e-ring by pressing the pliers closed.

6. Repeat step 3 through 5 to secure second wheel.

7. Remove the temporary blocks.

8. Attach the vibration mounts to the support leg with

1/4-20 x 3/4” capscrews and 1/4-20 lock nuts.

9. To aid support leg assembly, rest generator on cradle,

engine end down. Remove the existing hardware from

the left unit vibration mount with 13mm wrench. Use

the same hardware to attach the support leg.

10. Attach the other side of the support leg with a M8 x

20 mm cap screw and M8 lock nut. Rest generator on

wheels and support leg.

11. Attach handles to handle brackets on generator frame,

as shown in Figure 1, with M8 x 45 mm capscrews, flat

washers, nylon washers, and M8 lock nuts.

NOTE: Be sure to install the nylon washers between the

handle brackets on the generator frame and the brackets

on the handle assembly.

12. Loop handle pins to generator frame as shown in

Figure 1. Raise handles and insert handle pins to move

generator.

13. Check each fastener to ensure it is secure and the

tires are inflated between 15-40 PSI.

BEFORE STARTING THE

ENGINE

Add Engine Oil

• Place generator on a level surface.

• Refer to engine owner’s manual and follow oil

recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to

engine owner’s manual for recommendations.

NOTE: The generator assembly rotates on a prelubricated

and sealed ball bearing that requires no additional

lubrication for the life of the bearing.

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM (Engine

Modifications).

1. Use clean, fresh, regular UNLEADED fuel with a minimum

of 85 octane with equipment. DO NOT use fuel which

contains Methanol. DO NOT mix oil with fuel.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add regular unleaded fuel to fuel tank. Be careful

not to fill above the baffle.This allows adequate space

for fuel expansion (Figure 2).

4. Install fuel cap and wipe up any spilled fuel.

CAUTION

• Refer to engine manual for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine before it has

been properly filled with the recommended oil will result

in equipment failure.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

FUEL

TANK

Figure 2 — Typical Fuel Expansion Space

Baffle

1 2 3 4 5 6 7 8 9 10 11 12 ... 55 56

Comments to this Manuals

No comments

Briggs-stratton PRO6500 User Manual Page 7

Comments to this Manuals

Related products and manuals for Generators Briggs-stratton PRO6500